Methods of machine operation and use
Abstract:Before installing the strapping wire, turn the main switch to the "Off" position, lock the trigger lock, and remove the battery case. This tool can only use the matching strapping wire.
First, how to install the binding wire:
Note: Before installing the strapping wire, turn the main switch to the "Off" position, lock the trigger lock, and remove the battery case. This tool can only use the matching strapping wire.
1.. Press the wire feeder arm forward so that the wire feeder is open
2. Push the latch on the side cover of the cable tray upwards to make the side cover pop out
3 Take out the bundling coil, use tool pliers to take out the wire and cut off the bent part in front
4. When inserting the wire head, pay attention to the fact that the binding wire head cannot be bent or discounted when the wire head passes through the wire inlet horn, and the wire tray has a white dot face toward the inside, and then insert the wire head into the wire inlet horn, and immediately cover the side cover plate to scatter the wire.
5.. After the binding wire protrudes from the feed horn, it must pass through the middle groove of the left and right transmission gear. Extend into the inlet of the lead tube.
6. Open the wire feeding press arm to the left, so that the wire feeding press arm is restored to its original position, and the binding wire must be in the middle slot of the left and right transmission gear.
7. Before loading the battery box, ensure that the power is on or off and the start switch lock is locked
8. When installing the battery box, place the handle of the machine on the corresponding buckle of the battery box, push it in the horizontal direction, and hear the sound of "click", the battery box will be stuck to the correct position. To replace the battery case, press down on the red area on the front of the battery case, and then pull back the handle.
9. Machine automatic detection, open the start switch lock up push, open the power switch, buzzer "drop" a sound, the power indicator light, the wire outlet will automatically fall out of 5-10mm wire, at this time to complete the whole process of installing the strapping wire.
Attention:
1. When the battery is installed and the main switch and switch trigger lock are all closed, do not put your fingers or other parts near the strapping and rotating parts of the tool.
2. Do not try to switch the main switch quickly and frequently to avoid tool damage.
3. Do not touch your fingers or other parts of your body to the wire while working.
4. Lock the switch trigger lock when not using tools.
Note: Before installing the strapping wire, turn the main switch to the "Off" position, lock the trigger lock, and remove the battery case. This tool can only use the matching strapping wire.
1.. Press the wire feeder arm forward so that the wire feeder is open
2. Push the latch on the side cover of the cable tray upwards to make the side cover pop out
3 Take out the bundling coil, use tool pliers to take out the wire and cut off the bent part in front
4. When inserting the wire head, pay attention to the fact that the binding wire head cannot be bent or discounted when the wire head passes through the wire inlet horn, and the wire tray has a white dot face toward the inside, and then insert the wire head into the wire inlet horn, and immediately cover the side cover plate to scatter the wire.
5.. After the binding wire protrudes from the feed horn, it must pass through the middle groove of the left and right transmission gear. Extend into the inlet of the lead tube.
6. Open the wire feeding press arm to the left, so that the wire feeding press arm is restored to its original position, and the binding wire must be in the middle slot of the left and right transmission gear.
7. Before loading the battery box, ensure that the power is on or off and the start switch lock is locked
8. When installing the battery box, place the handle of the machine on the corresponding buckle of the battery box, push it in the horizontal direction, and hear the sound of "click", the battery box will be stuck to the correct position. To replace the battery case, press down on the red area on the front of the battery case, and then pull back the handle.
9. Machine automatic detection, open the start switch lock up push, open the power switch, buzzer "drop" a sound, the power indicator light, the wire outlet will automatically fall out of 5-10mm wire, at this time to complete the whole process of installing the strapping wire.
Attention:
1. When the battery is installed and the main switch and switch trigger lock are all closed, do not put your fingers or other parts near the strapping and rotating parts of the tool.
2. Do not try to switch the main switch quickly and frequently to avoid tool damage.
3. Do not touch your fingers or other parts of your body to the wire while working.
4. Lock the switch trigger lock when not using tools.